Differences

This shows you the differences between two versions of the page.

--- manual-config:snom-paplus [2026/02/26 15:41] – joe
+++ manual-config:snom-paplus [2026/02/26 16:15] (current) – joe
@@ Line 7: / Line 7: @@
 ===== STEP 1 =====
@@ Line 16: / Line 13: @@
 --------------------------------------------------------------------------------------------------------
-{{:manual-config:addphone-button.png?200| }}
+{{:manual-config:extensionspage.png?600|}}
 --------------------------------------------------------------------------------------------------------
-{{:manual-config:manual.png?200| }}
+{{:manual-config:manual_extension.png?600|}}
 --------------------------------------------------------------------------------------------------------
-**STEP 2:** Give the extension a name and an extension number and click **Save/Update**.
+===== STEP 2 =====
+Give the extension a name and an extension number and click **Save/Update**.
 **IMPORTANT**: The settings in the red boxes below are only used for this example. When you create your own extension manually, the information highlighted in the red box is **UNIQUE** to you.
@@ Line 31: / Line 31: @@
 --------------------------------------------------------------------------------------------------------
+===== STEP 3 =====
-**STEP 3:** In another tab, log into the SNOM PA1+ by typing in its IP address into the address bar. You will need to be on a network that can communicate with the device.
+In another tab, log into the SNOM PA1+ by typing in its IP address into the address bar. You will need to be on a network that can communicate with the device.
 Choose Identity 1 on the left side of the screen.
-**DO NOT USE THE SETTINGS LISTED IN THE EXAMPLE.** Use the settings from the manual extension you just created.
+**DO NOT USE THE SETTINGS LISTED IN THE EXAMPLE FROM STEP 2.** Use the settings from the manual extension you just created. Each manual extension has its own **unique** settings.
+{{:manual-config:identity_1.png?600|}}
 **Box 1:** This is the name you gave your extension. In our example, the extension was named SNOM PA, yours may be different.
@@ Line 48: / Line 55: @@
 --------------------------------------------------------------------------------------------------------
-{{:manual-config:identity_1.png?600|}}
+===== STEP 4 =====
---------------------------------------------------------------------------------------------------------
-**STEP 4:** Click the **NAT** tab and set **Keepalive interval** to 15 and **Number of Initial Keep-Alives on RTP port** to 2.
+Click the **NAT** tab and set **Keepalive interval** to 15 and **Number of Initial Keep-Alives on RTP port** to 2.
---------------------------------------------------------------------------------------------------------
 {{:manual-config:snom2.png?650| }}
+If you are configuring your SNOM for use as a ringer with a PA speaker, put this new manual extension in the group you want it to ring with and your setup is complete.
+If you want to use a PA speaker as a standalone intercom, click on the manual extension again and check the box for **Intercom Mode**. Use the extension given to dial the speaker in intercom mode. If your extension is 150, intercom mode will enable as extension 250.
+{{:manual-config:intercom.png?600|}}
 --------------------------------------------------------------------------------------------------------
-**STEP 5:** Click the **Advanced** option on the left side of the screen, pick the **SIP/RTP** tab and page down to the bottom:
+===== Multicast Paging Setup =====
+These settings are only necessary if you intend to use multicast paging.
+===== STEP 1 =====
+Click the **Advanced** option on the left side of the screen, pick the **SIP/RTP** tab and page down to the bottom:
 {{:manual-config:snommulticast.png?650| }}
+--------------------------------------------------------------------------------------------------------
 Enter a name for the paging group and its multicast address.
@@ Line 70: / Line 90: @@
 {{:manual-config:multicast-address.png?650| }}
+--------------------------------------------------------------------------------------------------------
 Click **Identity 1** again on the left side of the screen, then click the **SIP/RTP** tab. Add the multicast address and port to the **Multicast relay address** box:
 {{:manual-config:broadcast-relay.png?650| }}
 Click apply and the paging group should be ready to use by dialing the extension number. To configure another group, repeat this process with another manual extension and use Identity 2 through 4 to configure it.